Results 1 to 12 of 12
-
06-06-2011, 09:07 AM #1Web Hosting Master
- Join Date
- Mar 2009
- Posts
- 3,700
fatal error : controller monitor failed. controller not started
Hi,
i buy a server with X9SCM-F/Adaptec 2405/4*WD RE4 5003ABYX,
1. after booting,no matter how do i type "del",it always go to the screen as my attachment shows
2. when i type ctrl+a,it also go to the screen.
after running minutes,it will stop there,can i ask what should i do for a new server with Adaptec 2405 ?
thanxLast edited by ttgt; 06-06-2011 at 09:12 AM.
-
06-06-2011, 10:07 AM #2Web Hosting Master
- Join Date
- May 2004
- Location
- Atlanta, GA
- Posts
- 3,872
remove the adaptec and see whether you can get a normal boot. this could be caused by either a bad 2405 or bad riser card.
on X9 series SM board, to enter BIOS setup, you must hit F11, then select "setup" instead of the usual "del" key.
-
06-06-2011, 10:43 AM #3Web Hosting Master
- Join Date
- Mar 2009
- Posts
- 3,700
Hi,
1. i try to remote the riser card/raid card/no hd connect to board,and reboot,when i type "del",i can go into bios,when i type F11,it show show with my attachment.
2. i try to install the Adaptec 2405 with had are booting,it is under initialation now,as my 2nd picture.thanx
-
06-06-2011, 10:55 AM #4Web Hosting Master
- Join Date
- Mar 2009
- Posts
- 3,700
Hi,
the initialization still fail as my picture 1,and i take the picture of my raid card,it glisten with red lamp,as my 2nd picture,is any way to check the health of the raid card ? thanx
-
06-06-2011, 11:03 AM #5Web Hosting Master
- Join Date
- May 2004
- Location
- Atlanta, GA
- Posts
- 3,872
-
06-06-2011, 11:09 AM #6Web Hosting Master
- Join Date
- Mar 2009
- Posts
- 3,700
for normal,what messages or result will it show ? thanx
-
06-06-2011, 11:16 AM #7Web Hosting Master
- Join Date
- May 2004
- Location
- Atlanta, GA
- Posts
- 3,872
-
06-06-2011, 12:17 PM #8Disabled
- Join Date
- Jun 2004
- Location
- Hyderabad India
- Posts
- 1,103
does not apply' new machine , then just bad card or cables not connected properly
Last edited by Krazy; 06-06-2011 at 12:20 PM.
-
06-06-2011, 12:38 PM #9Web Hosting Master
- Join Date
- Mar 2009
- Posts
- 3,700
i think there is still some issue there,because still has error.thanx
-
06-06-2011, 07:52 PM #10Web Hosting Master
- Join Date
- May 2004
- Location
- Atlanta, GA
- Posts
- 3,872
well, the only thing left to do is to try a different 2405 card.
-
06-15-2011, 06:11 AM #11Web Hosting Master
- Join Date
- Mar 2009
- Posts
- 3,700
Hi,
after replacing a new 2405 card,i can boot into raid controller well,but i have some questions:
1.before i create array,can i go into bios well ? because no matter how click F11,it always stop at the page as my attachment,and i use ctrl+alt+del,it still not reboot at all and stay at the page.
2.for general,if i want to create raid 10,go into 2405 control and "create array" is enough? or i need to do any other deep setting for the raid card to let it run well ?
thanx
-
06-16-2011, 08:46 PM #12Web Hosting Master
- Join Date
- Mar 2009
- Posts
- 3,700
Hi,does anyone have experience with it? Thanx
Similar Threads
-
RAID Controller
By sly_cooper in forum Hosting Software and Control PanelsReplies: 4Last Post: 01-28-2011, 04:55 PM -
RAID controller failed on IBM RS/6000
By baemon in forum Hosting Security and TechnologyReplies: 0Last Post: 02-15-2007, 08:52 AM -
New GC controller
By death_entry in forum Web Hosting LoungeReplies: 2Last Post: 07-01-2004, 12:43 AM -
Hosting Controller
By rizwan65 in forum Hosting Software and Control PanelsReplies: 4Last Post: 01-09-2003, 10:46 AM -
Smart hosting controller admin error
By A Web Host in forum Hosting Security and TechnologyReplies: 4Last Post: 08-03-2002, 06:09 PM